Skip to main content

How to... set up a turntable

Record players are arguably the most temperamental of hi-fi components. Even the best are easily upset by inconsiderate positioning, poor adjustment or an inadequate support.

Get everything right though, and they can shine in a way that will make you wonder why we ever bothered with digital.

Most budget turntables come pre-assembled. These come with arm and cartridge attached and adjusted. So you should be good to go.

As you move up in price, say £500 and above, and it becomes more common that a certain amount of assembly is involved. You can get the supplying dealer to do this, but if you fancy doing the set-up yourself, it isn’t too difficult.

For those keen to have a go a decent tool kit is a must. The bare minimum is a good set of small Allen keys, a set of precision screwdrivers and a pair of long nose pliers along with an accurate spirit level. With these you can set-up most decks, including fitting and adjusting the tone arm and cartridge.


The first thing to get right is not the turntable, but the support it sits on. This has to be absolutely level. Any deviation will affect how well your record player works. The support should also be rigid and well controlled in terms of internal resonances.

Some decks respond well when placed on heavy supports other prefers lighter alternatives. Much of this depends on the structural behaviour of the deck itself and can only be decided by experimenting.

The issue of levelling doesn’t stop there. If your record player has adjustable feet make sure it sits flat, and if it has suspension ensure the platter is level too.

It all sounds a little obvious, but making sure everything sits level is vital, because you’ll never be able to optimise the performance of your deck if this aspect isn’t right, no matter how well the rest of the adjustments are done.


Most turntables come pre-fitted with a tone arm. If you want to change that, or have bought a more specialist deck that comes without an arm, you’ll need an appropriate arm board.

Turntable manufacturers should be able to supply a range of arm board options, which should suit just about any tone arm out there. In the worst case it isn’t too difficult to machine one to fit.

There are a number of adjustments on the tone arm. Its height has to be set so that the arm is parallel to the record’s surface when the cartridge sits in the groove.

It’s possible to fine-tune performance by altering this so that the arm bearing is a little higher or lower. This alters the angle at which the stylus tip meets the groove, but we’d start with it level.

Tracking Weight

Then there’s the tracking weight, which is adjusted by moving a counter-weight at the rear of the tone arm. The down force should be set according to the cartridge manufacturer’s recommendation, to start with at least.

If the tracking weight is set too high the sound becomes dull and ponderous. Too low and the presentation will turn thin and the cartridge won’t track the groove properly.

The last adjustment on the tone arm is that of bias. Bias is a sideways force on the cartridge to balance out the inward pull of the record groove. The bias is usually set to the same amount as the tracking weight.

MORE: See all our turntable reviews

As with the tracking weight don’t be afraid about playing around with the bias setting – mall changes can make notable difference.

It’s worth making sure the tone arm lead isn’t stressed and is positioned away from anything that runs on mains voltage. This will prevent excessive hum.

Most cartridges are mounted on the arm with a couple of bolts. That’s easy enough, if a touch fiddly. It’s trickier to accurately align it so that the stylus tip sits perfectly in line in the record groove.

Even small errors in alignment increase distortion massively, so take the time to get this right: most deck manufacturers include a suitable gauge.

Get all this right and you’ll have a deck working at its best. Enjoy.

MORE: Best turntables to buy in 2014

MORE: 10 of the best vinyl records to test your system

by Ketan Bharadia

Follow on Twitter

Join us on Facebook

Find us on Google+

Ketan Bharadia

Ketan Bharadia is the Technical Editor of What Hi-Fi? He's been been reviewing hi-fi, TV and home cinema equipment for over two decades, and over that time has covered thousands of products. Ketan works across the What Hi-Fi? brand including the website and magazine. His background is based in electronic and mechanical engineering.