7 posts / 0 new
Last post
RealX11's picture
Offline
Last seen: 9 months 2 weeks ago
Joined: 07/10/2013 - 11:59
Posts: 4
Yahama RX-V375 impendance (Ohms) Setup

Hello,

 

I bought "RX-V375 AVR" , "NS-PA120 5.0 speaker System" and "YAMAHA YST-SW 216 Subwoofer"   Speaker System from MediaMarkt Germany.
 
The impedance value of NS-PA120 5.0 speaker System is 6 ohms, but the factory value is 8 ohms.I tried 5 steps mentioned below on AVD machine, but I could not see "SP  IMP" menu.
 
1- Before connecting speakers, connect the power cable to an AC wall outlet.
2 - While holding down STRAIGHT on the front panel, press (power).
3 - Check that “SP IMP.” is displayed on the front display.
4 - Press STRAIGHT to select “6Ω MIN”.
5 - Press (power) to set the unit to standby mode and remove the
power cable from the AC wall o
 
 
To sum up, How can I make impedance value as 6 ohms on RX-V375 AVR, rather than 8 ohms?

 

Coult you help.

Petherick's picture
Offline
Last seen: 2 months 3 weeks ago
Joined: 29/10/2008 - 13:49
Posts: 468
Hi RealX11Only US and

Hi RealX11
Only US and Canadian models can be switched 6 or 8 ohms. I assume you are not in US or Canada...
For other models, the manual states "Use speakers with an impedance of at least 6 ohms", so your speakers should be fine.

RealX11's picture
Offline
Last seen: 9 months 2 weeks ago
Joined: 07/10/2013 - 11:59
Posts: 4
RE: Hi RealX11Only US and

Petherick wrote:
Hi RealX11 Only US and Canadian models can be switched 6 or 8 ohms. I assume you are not in US or Canada... For other models, the manual states "Use speakers with an impedance of at least 6 ohms", so your speakers should be fine.

 

The speaker I use is 6 ohms. The factory setting of AVR machine is 8 ohms.
Does not it create a problem?

Petherick's picture
Offline
Last seen: 2 months 3 weeks ago
Joined: 29/10/2008 - 13:49
Posts: 468
RE: Yahama RX-V375 impendance (Ohms) Setup

I am going by the user manual and the specifications here - http://europe.yamaha.com/en/products/audio-visual/av-receivers-amps/rx-v375_g/ which states 6 ohm speakers are suitable.

RealX11's picture
Offline
Last seen: 9 months 2 weeks ago
Joined: 07/10/2013 - 11:59
Posts: 4
RE: Yahama RX-V375 impendance (Ohms) Setup

Petherick wrote:

I am going by the user manual and the specifications here - http://europe.yamaha.com/en/products/audio-visual/av-receivers-amps/rx-v375_g/ which states 6 ohm speakers are suitable.

 

So,

Do not need to make any adjustments.
Right?

Petherick's picture
Offline
Last seen: 2 months 3 weeks ago
Joined: 29/10/2008 - 13:49
Posts: 468
RE: Yahama RX-V375 impendance (Ohms) Setup

Right!

RealX11's picture
Offline
Last seen: 9 months 2 weeks ago
Joined: 07/10/2013 - 11:59
Posts: 4
RE: Yahama RX-V375 impendance (Ohms) Setup

Petherick wrote:

Right!

 

Thank you Smile

Log in or register to post comments